采购电动餐桌 自动餐桌定制

 

采购电动餐桌 自动餐桌定制   电动餐台椅工厂的 注意事项

Precautions for electric dining table and chair factory

 主要施工工艺

 Main construction process

（1）电动餐台椅工厂的 清漆施工工艺： 打磨基层（清理木器表面→磨砂纸打光，磨平磨光，用湿布清扫干净）；采购电动餐桌 自动餐桌定制刷遍清漆（加入稀释液，漆膜快干）；满刮遍腻子,砂纸磨光（腻子修补钉眼和缝隙）；刷第二遍清漆,细砂纸磨光；刷第三遍清漆、磨光；木制至少5遍，水砂纸打磨退光,打蜡,擦亮。注意： 间隔,干透为止.夏季6小时,冬季24小时.现场保持清洁，无灰尘。温度在5摄氏度以上。

(1) The varnish construction process of the electric dining table and chair factory: polish the base layer (clean the surface of the wood→ polish with sandpaper, smooth and polish, and clean with wet cloth); Brush varnish (add diluent, paint film will dry quickly); Fully apply putty and polish with sandpaper (repair nail holes and gaps with putty); Brush the second coat of varnish and polish with fine abrasive paper; Brush the third coat of varnish and polish; Wood shall be polished, polished, waxed and polished at least 5 times with water sandpaper. Note: The site shall be kept clean and free of dust at intervals until it is completely dry. It lasts for 6 hours in summer and 24 hours in winter. The temperature is above 5 ℃.

（2）采购电动餐桌 自动餐桌电动餐台椅工厂的混色油漆施工工艺：打磨基层（清扫基层表面的灰尘,修补基层，用磨砂纸打平）；遍满刮腻子（调和腻子，光油、石膏、粉水3:6:1）→磨光→涂刷底漆（主漆：固化剂：稀释剂1:0.5:1，底漆厚度为1厘米左右，干燥4个小时）→细砂纸打磨→涂刷面漆（面漆：固化剂：稀释剂1:0.5:1，固化剂增加油漆附着度，稀释剂增加干燥性，太稠不便施工，太稀附着力不好）→复补腻子进行修补→磨光擦净第三遍面漆涂刷第二遍涂料→磨光→第三遍面漆→抛光打蜡。

(2) The construction process of mixed color paint in the electric dining table and chair factory: polish the base layer (clean the dust on the surface of the base layer, repair the base layer, and flatten it with abrasive paper); Fully apply putty (mixed putty, varnish, gypsum, powder water 3:6:1)&arr; Polishing→ Apply primer (main paint: curing agent: diluent 1:0.5:1, primer thickness is about 1cm, dry for 4 hours)&rar; Fine sanding→ Apply finish paint (finish paint: curing agent: diluent 1:0.5:1, curing agent increases paint adhesion, diluent increases dryness, too thick for construction, too thin for adhesion)&rar; Repair with putty→ Polish and wipe the third coat of finish paint and brush the second coat of paint→ Polishing→ The third finishing coat→ Polishing and waxing.

2．电动餐台椅工厂的施工要点清油涂刷的施工规范打磨基层是涂刷清漆的重要工序,应首先将木器表面的尘灰、油污等杂质清除干净。采购电动餐桌 自动餐桌上润油粉也是清漆涂刷的重要工序,施工时用棉丝蘸油粉涂抹在木器的表面上,用手来回揉擦,将油粉擦入到木材的察眼内。涂刷清油时,手握油刷要轻松自然,手指轻轻用力,以移动时不松动、不掉刷为准。

2. Key points for the construction of the electric dining table and chair factory. The construction specification for varnish painting. Grinding the base layer is an important process for varnish painting. First, dust, oil and other impurities on the surface of the wood should be removed. Applying oil powder is also an important process of varnish painting. During construction, use cotton thread dipped in oil powder to smear it on the surface of wood, rub it back and forth with hands, and rub the oil powder into the eye of wood. When applying clear oil, hold the oil brush in your hand easily and naturally, and gently force your fingers to ensure that the brush does not loosen or fall off when moving.

涂刷时要按照蘸次要多、每次少蘸油、操作时勤,顺刷的要求,依照先上后下、先难后易、先左后右、先里后外的顺序和横刷竖顺的操作方法施工。 .木质表面混油的施工规范基层处理时,除清理基层的杂物外,还应进行局部的腻子嵌补,打砂纸时应顺着木纹打磨。采购电动餐桌 自动餐桌在涂刷面层前,应用漆片(虫胶漆)对有较大色差和木脂的节疤处进行封底。应在基层涂干性油或清泊,涂刷干性油层要所有部位均匀刷遍,不能漏刷。底子油干透后,满刮遍腻子,干后以手工砂纸打磨,然后补高强度腻子,腻子以挑丝不倒为准。涂刷面层油漆时,应先用细砂纸打磨。

The painting shall be carried out in accordance with the requirements of more dips, less dips of oil each time, frequent operation and smooth brushing, and in accordance with the sequence of top to bottom, first difficult to easy, first left to right, first inside to outside, and the operation method of horizontal and vertical brushing Specification for construction of oil mixed on wood surface During base course treatment, in addition to cleaning the sundries on the base course, local putty shall also be inlaid, and sandpaper shall be polished along the wood grain. Before painting the surface layer, the knots with large color difference and wood grease shall be sealed with paint chips (shellac paint). The base layer shall be coated with dry oil or clear berth, and all parts of the dry oil layer shall be evenly brushed without omission. After the primer oil is dry, it shall be fully applied with putty. After it is dry, it shall be polished with manual sandpaper, and then the high-strength putty shall be added. The putty shall be subject to no tipping. When painting the surface layer, it should be polished with fine sandpaper first.