如何安装电动餐桌，安装前准备工作该注意什么

电动餐桌一般酒店饭店应用较多，但随着科技在家具产品中应用的普及，很多家庭用户也会选择电动餐桌，电动餐桌和普通餐桌还不一样，其安装也会复杂一些，下面来看看电动餐桌的安装方法吧。

Electric dining tables are commonly used in hotels and restaurants, but with the popularization of technology in furniture products, many household users also choose electric dining tables. Electric dining tables are different from regular dining tables and their installation may be more complex. Let's take a look at the installation methods of electric dining tables.

一、电动餐桌安装前准备工作：

1、 Preparation before installing the electric dining table:

1.选好位置确定中心将滚筒放好，放平;

1. Select a suitable position to determine the center and place the drum flat;

2.钢架放在滚筒上并调平;

2. Place the steel frame on the drum and level it;

3.转盘放钢架上并调平;

3. Place the turntable on the steel frame and level it;

4.连接电机控制器电源，查看转动是否正常;

4. Connect the power supply to the motor controller and check if the rotation is normal;

5.安装脚和围板;

5. Install feet and hoarding;

6.安装环形餐台;

6. Install a circular dining table;

7.接通电源，安装结束。

7. Turn on the power and the installation is complete.

二、酒店家具电动餐桌安装详细步骤

2、 Detailed steps for installing electric dining tables in hotel furniture

1.首先使用尺子测量安装后桌子的总体大小(打开尺子调整到桌子的半径大小，放在滚筒的中心位置转动，调整到合适位置)，然后将滚筒平放在合适的安装位置;

1. Firstly, use a ruler to measure the overall size of the installed table (open the ruler to adjust to the radius of the table, place it in the center of the drum and rotate it to the appropriate position), and then place the drum flat in the appropriate installation position;

2.将钢架平放在滚筒上，使二者同心，安装好螺丝，固定;

2. Place the steel frame flat on the drum, make them concentric, install the screws, and fix them;

3.再将转盘(玻璃板、理石板或木板等)平放在钢架上，并使三者同心，安装好螺丝，固定;

3. Place the turntable (glass board, marble board, or wooden board, etc.) flat on the steel frame and make them concentric. Install the screws and fix them;

(如果餐桌的转盘配备电磁炉，此时放置电磁炉，并将电磁炉的插头插入滚筒的插座上，将滚筒上的插线板用螺丝固定到转盘上)

(If the turntable of the dining table is equipped with an induction cooker, place the induction cooker at this time and insert the plug of the induction cooker into the socket of the drum. Fix the plug board on the drum to the turntable with screws)

4.滚筒上电机连接控制器，再接通电源，查看转盘转动是否正常，正常后切断电源;

4. Connect the motor on the drum to the controller, then connect the power supply, check if the rotary table rotates normally, and then cut off the power supply;

5.安装脚和围板，并调平，脚和围板用螺丝固定好(围板安装快完成时，注意在围板有孔的地方安装控制器，并与滚筒上电机相连);

5. Install the feet and shroud, level them, and secure them with screws (when the shroud installation is almost complete, pay attention to installing the controller in the hole on the shroud and connecting it to the motor on the drum);

6.安装环形餐台，餐台与餐台调平并用螺丝固定，再与脚用螺丝固定;

6. Install a circular dining table, level it with the dining table and fix it with screws, and then fix it with screws to the feet;

7.接入电源，打开开关即可使用。(开关由用户自设，可用墙壁开关，也可用遥控开关。建议由服务员操作。上菜开始转，客人走后停。一般餐桌都配有遥控开关)

7. Connect the power supply and turn on the switch to use it. (The switch is set by the user, and can be either a wall switch or a remote control switch. It is recommended to be operated by the waiter. It starts to turn when the dish is served and stops when the guest leaves. Generally, the dining table is equipped with a remote control switch)